|
VACUUM CUPS |
|
Mini Vacuum Cups |
Standard Round Vacuum
Cups |
Linear Cylinder with Vacuum Generator |
|
|
|
|
|
The SM1 to SM6
sized vacuum cups are delivered with a hollow stud fitting. The
corresponding external thread is shown in the table as dimension
"M". |
The SG series
vacuum cups are delivered with a hollow stud fitting. The
corresponding
external thread is shown in the table as dimension
"M". |
Linear Cylinders are available in a variety of sizes
|
|
Knobbed Round Suction Cup |
Knobbed Round Suction Cup with Aluminum Backing Plate |
Knobbed Round Suction Cup with Aluminum Backing Plate and Ball Joint |
|
|
|
|
The small
knobs of the Knobbed
Vacuum cup effectively
maintain vacuum force while preventing
total adhesion of the cups sealing lips during vacuum. The rigid
sealing lips also offer greater stability
against lateral forces. Like all of our vacuum
cups these can be easily plugged in and replaced.
|
When handling
large parts, large stable vacuum cups are necessary. There are
two versions available: a) with an external thread for
connecting to vacuum pumps; or b) with an external thread and a
built-in vacuum generator.
There are separate part numbers for the fittings (SA22 or
SAV22) and the suction pad with aluminum backing plate (PNS...A)
|
The Spring Loaded
Knobbed Vacuum Cups (with ball
joint) are characterized by their locking system. The upper
spring ensures that there is no recoil when lifting the part.
The return spring can extend 25 mm ( a 50 mm version is
currently being developed) and is secured against rotation.
Consequently, parts can be picked up and placed accurately. A
maximum compensation angle of +15º is provided by the ball
joint. |
|
Round Bellows Cup with Single Pleat (short stroke) |
Round Bellows Cup with 2 Pleats (long stroke) |
Torroidal
Vacuum Cups |
|
|
|
|
The folds expand and
contract evenly, like an accordion. This guarantees high retaining
power because the sealing surface adapts elastically to the
workpiece in any position. In addition, in the case of lighter
parts there is a lifting effect...once the part has been
gripped, the folds close up and lift the part upwards.
|
The folds expand and
contract evenly, like an accordion. This guarantees high retaining
power because the sealing surface adapts elastically to the
workpiece in any position. In addition, in the case of lighter
parts there is a lifting effect... once the part has been gripped,
the folds close up and lift the part upwards.
|
The design is
ideal for picking up washers, seals, o-rings, CDs. tubes,
perforated plates and more.The middle hole is covered by the
insertion of a rubber core (SK) within the outer vacuum cup. The
vacuum is pulled through slots on the side of the core. The rubber
cores are available in different diameters to cover holes of
different sizes. Outer vacuum cups are attachable to fittings with
external or internal threads, with or without vacuum generator.
|
|
Oval
Vacuum Cups |
Oval Vacuum Cups with Aluminum Backing Plate |
Oval Vacuum Cups with Aluminum Backing Plate and Ball Joint |
|
|
|
Suitable for
applications in which heavy loads require a larger gripping
surface. The Oval Vacuum Cups offer a greater area and vacuum
power than round vacuum cups and are ideal for rectangular or oval
shaped workpieces.
The knobs on these oval cups prevent them from collapsing under
vacuum and losing their effective surface areas.
|
When handling large
parts, large stable vacuum cups are necessary. There are two
versions available: a) with an external thread for connecting to
vacuum pumps; or b) with an external thread and a built-in vacuum
generator. There are separate part numbers for the fittings (SA22
or SAV22) and the vacuum pad with aluminum backing plate (PV...A).
|
The Spring Loaded
Oval Vacuum Cups (with ball joint) are characterized by their
locking system. The upper spring ensures that there is no recoil
when lifting the part. The return spring can extend 25 mm ( a 50
mm version is currently being developed) and is secured against
rotation. Consequently, parts can be picked up and placed
accurately. A maximum compensation angle of +15º is provided by
the ball joint.
|
|
Oval Bellows Vacuum Cups |
Inline Vacuum Generators |
Multi-Chamber Vacuum Generators |
|
|
|
|
|
When vacuum is
applied, the bellows "pleats" compress, lifting the
workpiece.
|
Internal/external threaded mounts
|
for applications requiring large vacuum volume
|
